| 1. | The theoretical curves are reversed respectively
分别对理论曲线进行了反演。 |
| 2. | At the same time , we compare the force - velocity theoretical curve with the experiment , the result shows that they are identical basically
同时还将力-速度的曲线与实验做了比较，结果表明二者定性吻合。 |
| 3. | Meanwhile , the fitted curves of analytical solutions are compared with the field measured ones , and it is proved that the theoretical curves are in good agreement with that obtained from the field measurement
同时将本文解应用于桩基动测曲线分析工作中，通过与工程实测曲线的反演拟合和正演分析，检验了本文理论解的实用性。 |
| 4. | The comprehensive research of typical wells in water - yield pattern shows that the theoretical curves are accordant with actual situation , indicating this method is applicable to analysis and prediction of water - yielding pattern in such a reservoir
对典型井的产水规律综合研究表明，理论曲线与油藏实际产水情况比较吻合，说明该方法对薄层底水油藏产水规律分析预测具有较好的适用性。 |
| 5. | 4 . the theoretical curves v ( f , [ atp ] ) and r ( f , [ atp ] ) under the steady state are compared to experiments when a load acts on the molecular motor , the result is that these theoretical curves accord basically with experiments , which illustrates better the kinetic behaviors of a molecular motor
将分子马达拖动负载时的稳态速度v和随机参数r随atp浓度[ atp ]的理论变化拟合曲线同实验进行了比较，结果表明：拟合曲线与实验基本吻合，较好地说明了马达在拖动负载运动时的各种动力学行为。 |
| 6. | The bragg diffraction efficiency of gows in bismuth - doped yig film is caculated by considering the edge cut - off effect . the obtained theoretical curve is basically agreement with the experimental results . it is shown that the diffraction performance for mo bragg cells can be greatly increased by using an appropriately nonuniform bias field
2 .考虑到边缘截止效应,论文中计算了静磁正向体波对导波光的衍射效率,理论结果与实验符合;从而表明,与均匀场情形相比,适当不均匀场可以大大提高磁光bragg器件的衍射效率。 |
| 7. | Exciting method is used to measure the damping , the four damping coefficients of the radial part and a damping coefficient of the thrust part can be obtained though hammering the testing bearing which is in a equilibrium position . based on the testing data , the dynamic characteristic curves of the radial - thrust floating ring hybrid bearing are drawn and compared with the theoretical curves
采用激振法测量轴承的阻尼，对处于平衡位置的测试轴承分别沿水平方向、上45度方向及轴向进行锤击，根据锤击法原理求得各个转速下轴承径向部分内、外膜总阻尼系数以及推力部分内、外膜总阻尼系数。 |
| 8. | In this paper , on basis of the current machining state , a testing principle on aspheric surface is put forward to , the principle is a kind of touching method by testing the meridian of aspheric surface and comparing it with the theoretical curve , so surface figure error is got . according to this principle , mechanical structure is designed and electric - control system is researched
本文首先基于现阶段非球面的加工状况，提出了用接触式检测非球面的子午面面形曲线并与理论曲线相比较，从而得到非球面面形误差的检测原理，并根据该原理进行了机械结构的总体设计和电控系统的研究。 |
| 9. | The results showed that the stress - strain realtionship of pt could be expressed with exponential functions , and there were significant differeces between the normal group and the immobilized group in their theoretical curves of stress - strain relationship and two material constants of pt . also , significant differences were found in tensile strength and tangent modulus between the two groups , but the maximum load of pt in the immobilized group did not decrease significantly
结果显示：正常组与制动组间髌韧带的应力-应变关系理论曲线有明显不同，其材料常数亦有显著差异；制动组髌韧带的极限强度和弹性模量较正常组均有明显下降，其极限载荷下降不明显。 |
| 10. | After the dynamical analysis , the theoretical curve of the stationary sorting turnout is formed . based on the result , a dynamic simulate experiment by computer is done . as a result , i find that the theoretic results meet the fact and the designation is feasible through comparing and analyzing the experimental and theoretic data
通过对系统的动力分析，从理论上构造出了推块式分拣机固定分拣道岔的曲线模型，并对该曲线模型进行了计算机动态仿真实验，对所得的仿真实验数据进行了比较与分析，论证了理论研究结果的正确性与可行性。 |
